-
1/2-20 CONE NUT 60 DEGREE TAPER -
2000# AXLE 63 1/2" HUB FACE 51 3/4" S.C. WITH HUBS - GALVANIZED -
U-BOLT KIT COMPLETE U-BOLTS, NUTS AND TIE PLATES -
DUST CAP WITH RUBBER GREASE PLUG -
SPRING SHACKLE HOLDER WITH ( 2 ) 9/16 " NYLON BUSHINGS (HOLDER/BUSHINGS ONLY) -
SPRING SHACKLE HOLDER COMPLETE WITH SHACKLE, BUSHINGS, BOLTS, AND NUTS -
1 LEAF SPRING COMPLETE WITH SHACKLE HOLDER,SHACKLE,BUSHINGS,BOLTS AND NUTS -
WIRING HARNESS, FRONT AND REAR -
LICENSE PLATE BRACKET BLACK PLASTIC -
LED TAIL LIGHT (RIGHT SIDE / PASSENGER SIDE) -
LED TAIL LIGHT (LEFT SIDE/DRIVERS SIDE) -
1/4 X 2 X 6 1/2" TAIL LIGHT BRACKET (NF) -
3/16 X 1 3/8 X 1 5/8 L X 3 3/16" (NF) TONGUE TO CROSSMEMBER -
1/8 X 4 X 8 1/2 REAR CROSSMEMBER ANGLE PLATE 45 DEGREES (NF) -
TX-4 SUB RAIL CLIP WITH THREE HOLES (ANODIZED) - LEFT/RIGHT SAME -
TX-1112 SIDERAIL 33" (NF) -
TX-10 (NF) 87" FRONT TONGUE SECTION - DRILLED FOR COUPLER -
TX-10 (NF) 87" REAR TONGUE SECTION -
AMBER MARKER CLEARANCE LIGHT WITH REFLECTOR -
TX-8 5-3/4" LENGTH FOR LED AMBER MARKER LIGHTS 4-263C -
1/2" FLAT WASHER SHEARED FOR COUPLER -
1 7/8" COUPLER FOR 2 1/2" WIDE TONGUE, 2000 LB. CAPACITY. -
3/8-16 LARGE FLANGE NYLON INSERT HEX LOCK NUTS 7/8" FLANGE (MAGNI 17) (PACKAGE of 15) -
3/8-16 x 3/4 REPAIR T-BOLTS (PACKAGE of 15) -
3/8-16 x 3/4 T-BOLTS (PACKAGE of 15) -
DECK MOUNT MAST CARRIER WITH 4 SUCTION CUP LEGS -
AFTER MAST STAND 10" WITH 3/8" PINS -
WINCH POST WITH CAP FOR ALL SUT TRAILERS -
MEDIUM WINCH 1400# CAPACITY -
SWIVEL BOW SUPPORT FOR LASER SERIES ONLY -
SPECIAL SPARE TIRE CARRIER FOR LASER TRAILERS ONLY. -
LASER BOW CLAMP, 1/4 X 1 1/8 X 13 1/2" NF, INCLUDES VINYL CAP, TOW RIVETS, FOUR PRONG KNOB AND 1 3/4" T-BOLTS WITH LOCKNUT -
3/8 ID X 2" OD 1/8" THICK LARGE NEOPRENE WASHER -
SMALL PLASTIC FENDER SILVER DRILLED. -
SMALL PLASTIC FENDER COMPLETE WITH BOLTS, NUTS, WASHERS -
SPRING SHACKLE HOLDER WITH ( 2 ) 9/16 " NYLON BUSHINGS (HOLDER/BUSHINGS ONLY) -
SPRING SHACKLE HOLDER COMPLETE WITH SHACKLE, BUSHINGS, BOLTS, AND NUTS -
1 LEAF SPRING COMPLETE WITH SHACKLE HOLDER,SHACKLE,BUSHINGS,BOLTS AND NUTS -
1/2-20 CONE NUT 60 DEGREE TAPER -
SPARE 4.80 X 12" CLR TIRE ON 4-HOLE GALVANIZED WHEEL -
SPARE 4.80 X 8" TIRE AND GALVANIZED WHEEL, 4" BOLT CIRCLE ON 4 HOLE WHEEL 590# CAP -
DUST CAP WITH RUBBER GREASE PLUG -
2000# AXLE 67 1/4" HUB FACE 57 1/4" S.C. WITH HUBS - GALVANIZED -
LICENSE PLATE BRACKET BLACK PLASTIC -
LED TAIL LIGHT (LEFT SIDE/DRIVERS SIDE) -
LED TAIL LIGHT (RIGHT SIDE / PASSENGER SIDE) -
AMBER MARKER CLEARANCE LIGHT WITH REFLECTOR -
0.100 x 1" x 2" L x 4" ANGLE for LED AMBER MARKER LIGHT (ANODIZED) -
1/4 X 2 X 16" TONGUE SKID (NF) -
1 7/8" COUPLER FOR 2 1/2" WIDE TONGUE, 2000 LB CAPACITY
